Article 5: Prestressed Anchor, Prestressing Equipment and Stressing Equipment for Civil Bridge Construction

This article is brief introduction of what materials need to use and how to install stressing equipment in bridges construction.

Henan Prestressing Equipment Co., Limited is a PT Manufacturer from China, our full products range for post tensioning and pre-strssing construction:

1. Materials: pc strand, YJM anchor system(monostrand anchor, multistrands anchor), ducts(metal ducts, HDPE plastic ducts).

2. Equipment: Hydraulic Jack(QYC mono jack, YDC multi-strand tensioning jack), electric oil pump, YH30 embossing machie(onion jack), GYJ500 extrusion machine, ZG130 ducts making machine, grouting pump and mixer for post tensioning),Intelligent Tension System Equipment.

Following my last article 4, after installation prestressed strand and steel duct. The next step is prepare prestressed anchor such as stressed end anchor and dead end anchor system, stressed end anchor include stressed end anchor block, working wedges, anchor bearing plate, and spiral reinforcement rings. Dead end anchor system include dead end anchor(or somewhere called "swages") springs, dead end steel plate, and spiral reinforcement rings.

We supply stressed anchor ranges and models as followings:

Stressed end multistrands anchor system: from 2 strands to 55 strands.

Stressed end monostrand anchor system: for 12.7mm or for 15.24mm prestressed strand.

Stressed end flat anchor system: for 2 strands, 3 strands, 4 strands, 5 strands.

Stressed end ground anchor system: for mining, dams,anchor drilling, rock and slope reinforcement.

Dead end anchor system: from 1 strands to 55 strands, etc.

The following is picture of prestressing work for bridge construction

Post-Tension in bridge construction is usually taken tensioning from two sides(one side is stressing-end, and the other side is dead end).

First, installation of stressing end anchor system

Second, installation of dead end anchor system

Use GYJ500A Compression Making Machine for making P Type Dead End Anchor

P Type Dead End Anchor Before Extrusion

P Type Dead End Anchor After Extrusion

Sometimes will use 5mm, 7mm, 9mm diameter pc steel wire and 18mm, 25mm, 28mm, 32mm steel rebar anchor in prestressing work. PC steel wire is also used in prestressed concrete work such as precast factory, hollow core slab, concrete pole, concrete column, etc.PC Steel Wire is used tensioned by monostrand jack such as QYC270 monostrand jack, YDC240(24 tons) monostrand jack, etc. We also supply power pack(stressed pump) for monostrand stressing work.

The steel rebar anchor is mostly used in bridges construction and buildings construction, the steel bar anchor system including: screw nuts, steel bar, anchor bearing plate, spiral reinforcing ring. Steel rebar anchor tensioned by YDC series of Hollow Plunger Jack, such as from YDC1000(100 tons) to YDC1200(1200 tons). We also supply its power pack(stressed pump) for post tension and prestressing.

Steel Wire Button Heading Machine for 5mm, 7mm 9mm wires.

5mm, 7mm 9mm pc steel wires after button heading

Steel Rebar Anchor System for Building Construction

Steel Rebar Anchor System for Bridge Construction

The galvanized metal duct have been installed well in bridge construction

Prestressed strand wire have been feed through into post tenion metal duct

About Mr. Jason Wang

Jason Wang is our sales manager who have been worked for our factory for many years. He is very experienced in exporting and know different requirement and needs of projects vary from customers from different countries. If you need any prestressed anchor system and prestressed equipment kindly please contact with him directly by following office email: sales@pt-concrete.com

Contact With Us:

Jason Wang

Sales Manager

Henan Prestressing Equipment Co., Limited

Skype : jason.wang569

Email Address: sales@pt-concrete.com

Mobile ＆ Whattsapp(WeChat) No.: +8613673713569

Tel: +86-0371-63228879, Fax: +86-0371-63228879

Thank you!